侵彻环境下两种钨合金的细观响应特性

本文实验发现具有较大密度和较高速度的93W钨合金长杆模拟弹的穿靶深度反而比密度较小，速度较低的90W钨合金长杆弹的穿靶深度小．针对这一现象，本文从两种材料在侵彻环境下的细观响应特性的差异上给出了有实验根据的合理分析，结论是90W在侵彻环境下较易于形成绝热剪切带，从而在弹头部发生“自锐化”效应所致．     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

A proof of Howard’s conjecture in homogeneous parallel shear flows

A rigorous mathematical proof of Howard's conjecture which states that the growth rate of an arbitrary unstable wave must approach zero, as the wave length decreases to zero, in the linear instability of nonviscous homogeneous parallel shear flows, is presented here for the first time under the restriction of the boundedness of the second derivative of the basic velocity field with respect to the vertical coordinate in the concerned flow domain.     

Separation of screw-sensed particles in a homogeneous shear field

The Stokes motions of three-dimensional screw-sensed slender particles in a homogeneous shear field are investigated, including the effects of buoyancy. Conclusions are drawn about the possibility of achieving a separation of mixtures of right- and left-handed particles. The linearity of the Stokes equations allows complex flows to be solved by adding the effects of the several terms which describe the flow in which the particle is immersed. The homogeneous shear flow considered here consists of three such terms; solutions for a series of 12 unit motions are sufficient to determine the hydrodynamic resistance tensors. The forces and torques experienced by screw-sensed particles are calculated from these 51 resistance tensors, using slender-filament theory. The results allow an estimate of the range of buoyancy parameters for which gravitational sedimentation can be neglected. The fundamental component of the particle motion is a rotation, at approximately the same angular velocity as that of the fluid. Superimposed on this are variations, of large period, in the particle orientation. A phase plane analysis is used to find the terminal orientations. Very long calculation times are required for the phase portrait. An approximate method based on azimuthally-averaged equations is developed to avoid the requirements for long time integration.     

An unflexural refined model of deformation of multilayered plates on an undeformable foundation

The stress-strain state of multilayered plates on an undeformable foundation is investigated. The design diagram of a transversely loaded plate is formed by supplementing it with a symmetric one about the contact surface of the foundation. The double-thickness plate obtained becomes loaded bilaterally and symmetrically about its midsurface. In such a way, only unflexural deformations can be modeled, which reduces the number of unknowns and the general order of differentiation of the resolving system of equations. The refined continual model developed takes into account the deformations of transverse shear and transverse compression in high iterative approximations. The cases of a rigid contact between the foundation and the plate and frictionless slip of the plate over the foundation are considered. Calculations confirm the efficiency of such an approach, which allows one to obtain solutions qualitatively and quantitatively close to three-dimensional ones. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 42, No. 5, pp. 643–654, September–October, 2006.     

切变模量和转动惯量实验的改进

设计了一种基于垂直轴定理的新型吊钩,对切变模量和转动惯量实验进行了改进,使之成为既可测定金属丝切变模量和环、柱等刚体的转动惯量,又可验证反映转动惯量重要性质的平行轴定理及垂直轴定理的多功能实验仪.     

透镜初级球差的横向剪切干涉条纹研究

利用玻璃平行平板构成简单的横向剪切干涉仪可以观察到单薄透镜形成的准直光束的剪切干涉条纹,由干涉条纹分布求出对应的几何像差和离焦量.用焦距为190 mm的单薄透镜做实验,实验结果与计算机模拟结果符合,说明可以从剪切干涉条纹的分布求出透镜的轴向调整误差和初级球差.     

考虑材料熔化潜热的高温高压本构

本文在修正的SCG模型基础上，提出了一种考虑了熔化潜热的高温高压本构.该本构所给出的铝的剪切模量的变化分为三个阶段：加工硬化，温度软化和熔化，并在完全熔化点处变为零.并且在前两个阶段，计算的结果与修正的SCG模型所给出的剪切模量的差别不超过4%，这一差别是在动高压实验误差范围之内的，在熔化区所给出的剪切模量与现有的实验数据相符合. 关键词： 剪切模量 熔化潜热 修正的SCG模型 动高压实验     

钢丝的切变模量与扭转角度关系

研究了钢丝的切变模量随其扭转角度变化而变化的情况,观察到扭转角大于某一角度时,切变模量趋于定值的规律,得出扭摆实验准确测量的方法.     

Elastic and Thermophysical Properties of Poly(Vinyl Chloride) and Chlorinated Polyethylene Blends

The results of experimental and theoretical investigations of elastic and thermophysical properties of poly(vinyl chloride) (PVC) and chlorinated polyethylene (CPE) blends are presented. Eight types of specimens with different ratios of weight contents of PVC and CPE (PVC/CPE = 100/0, 90/10, 80/20, 60/40, 40/60, 20/80, 10/90, and 0/100) were tested. The effect of blend composition on the elastic constants (tensile and shear modulus) is discussed. The data on the thermal conductivity, thermal diffusivity, and heat capacity of the blends investigated are also presented.